2014:Robot Sensors/Motors/Lights/Controls Map

Sensors

NOTE: each of these should also have a line in the appropriate (e.g. or ) (the "IO Map Updated?" column in the following table indicates if this was done)

Subsystem	Description (brief)	Type	Model#	Controlled By (/)	IO Map Updated?	Operation Details (including when broken)	Output Level	Notes
Intake	Detects intake position	Potentiometer	3852A-282-104AL	Analog	Yes	Sensor which detects the angle of the intake bar
Shooter	Detect kicker speed A	Optical shaft encoder sensor	E4P?	Digital	yes	Sensor detects shaft rotation to sense how fast the gear is rotating (Could also use shaft encoder on motor transmission ?)
Shooter	Detect kicker speed B	Optical shaft encoder sensor	E4P?	Digital	Yes
Shooter	Detect high kicker gear teeth	Optical flag	Limit Switch	Digital	Yes	additional check on kicker rotation to account for chain/gear slop
Shooter	Detects kicker low position	Optical flag sensor	Banner Sensor	Digital	yes	Senses flag that's connected to gear and detects whenever kicker is in low position
Shooter	Detect kicker high position	Optical flag sensor	Limit Switch	Digital	yes
Intake	Detects intake position	Potentiometer	3852A-282-104AL	Analog	yes	Sensor which detects the angle of the intake bar - redundant sensor
Intake	Detects ball presence on top of bumper	Optical flag	Banner Sensor	Digital	yes	Detects if ball is on top of the bumper.
Drivetrain	Left Encoder, Phase A	Shaft encoder	E4P	Digital	yes
Drivetrain	Left Encoder, Phase B	Shaft encoder	E4P	Digital	yes
Drivetrain	Right Encoder, Phase A	Shaft encoder	E4P	Digital	yes
Drivetrain	Right Encoder, phase B	Shaft encoder	E4P	Digital	yes

 

 

Motors

NOTE: each of these should also have a line in the appropriate (e.g. or or ) (the "IO Map Updated?" column in the following table indicates if this was done)

Subsystem	Description (brief)	Type	Model#	Controlled By (//)	IO Map Updated?	Operation Details (including when broken)	Notes
Drivetrain	Left Front Drive	CIM	TBD	CAN	Yes	TBD
Drivetrain	Left Rear Drive	CIM	TBD	CAN	Yes	TBD
Drivetrain	Right Front Drive	CIM	TBD	CAN	Yes	TBD
Drivetrain	Right Rear Drive	CIM	TBD	CAN	Yes	TBD
Shooter	front left Kicker arm	CIM	AM802	CAN or PWM	Yes	spins at full power in one direction, spins to 2 points	PWM / CAN TBD shortly
Shooter	mid left Kicker arm	CIM	AM802	CAN or PWM	Yes	spins at full power in one direction, spins to 2 points	PWM / CAN TBD shortly
Shooter	back left Kicker arm	Mini CIM	2501BL	CAN or PWM	Yes	spins at full power in one direction, spins to 2 points	PWM / CAN TBD shortly
Shooter	right front Kicker arm	Mini CIM	2493BL	CAN or PWM	Yes	spins at full power in one direction, spins to 2 points	PWM / CAN TBD shortly
Shooter	right mid Kicker arm	Mini CIM	2493BL	CAN or PWM	Yes	spins at full power in one direction, spins to 2 points	PWM / CAN TBD shortly
Shooter	right back Kicker arm	Mini CIM	2493BL	CAN or PWM	yes	spins at full power in one direction, spins to 2 points	PWM / CAN TBD shortly
Intake	roller	550/775	TBD	CAN or PWM	Yes	TBD
Shooter	cradle lift	775&PG71	TBD	CAN or PWM	YES	TBD

Servors/Actuators

NOTE: each of these should also have a line in the appropriate IO Map table (e.g. PWM or Relay) (the "IO Map Updated?" column in the following table indicates if this was done)

Subsystem	Description (brief)	Type	Model#	Controlled By (PWM/Relay)	IO Map Updated?	Operation Details (including when broken)	Notes

Lights (on robot)

NOTE: each of these should also have a line in the appropriate IO Map table (e.g. Relay or GPIO or I2C) (the "IO Map Updated?" column in the following table indicates if this was done)

Subsystem	Description (brief)	Type	Model#	Controlled By (Relay/GPIO/I2C)	IO Map Updated?	Location	Used By (driver/human/alliance)	Operation	Notes
	Camera Light	Green LED Ring		TBD	No	mounted to the camera	robot	Turned on in autonomous mode to 'light up' reflective tape so the robot can determine the hot goal	uses 12V

Operator Controls

Joystick 1 (Driver Left) Attack3 

Button/Axis	Description (brief)	Operation	Notes
1	Turbo	Make da robot go fast	Both sides
2	Slow	Make da robot go slow	Both sides
3
4
5
6	Debug Drive
7	Debug Intake
8
9
10	Debug Kicker
11	Debug Miscellaneous
12	n/a
X-axis
Y-axis	Left Wheels	Controls both left side motors. Pushing the joystick forward (away from driver) will move the robot forward. Pulling the joystick backwards (towards driver) will move the robot backwards.	Shooter is the 'front'
Z-axis

Joystick 2 (Driver Right)

Button/Axis	Description (brief)	Operation	Notes
1	Turbo	Robot turbo	Controls both sides
2	Slow	robot slow
3
4
5
6
7
8
9
10
11
12	n/a
X-axis
Y-axis	Right Wheels	Controls both right side motors. Pushing the joystick forward (away from driver) will move the robot forward. Pulling the joystick backwards (towards driver) will move the robot backwards.	Shooter is the 'front'
Z-axis

Joystick 3 (Aux Driver)

Button/Axis	Description (brief)	Operation	Notes
1	Acquire Ball	Intake wheels spin such the ball is moved onto the robot.
2
3	Pass Ball Slow	Intake wheels spin such the ball is moved out of the robot. This will be a 'slow' rate to allow for a short pass to a close by robot.
4	Pass Ball Fast	Intake wheels spin such the ball is moved out of the robot. This will be the fastest it can be, allowing for a long pass.
5
6
7
8
9
10
11
12
X-axis
Y-axis	Intake	Moves intake in/out (up/down)	When joystick is pushed forward (away from driver) the intake will got out (extend away from robot).
Z-axis

Joystick 4 (Aux Controls/Extended IO)

Button/Axis	Description (brief)	Operation	Notes
1	Truss Shot	shoot with enough strength to get over the truss	This will be the 3D printed lightning bolt).
2	High goal shot	Shott with enough strength to get into the high goal from a fixed distance.	This will be the 3D printed Gear.
3	Manual shoot	Shoot at  speed of manual power	this is the push in the push potentiometer
4	TBD	nothing yet	Really called the missle switch but i couldnt call it that because of mr byers.
5	Auto Choice 1	will run auto mode 1	The 3 way switch has an up down and off
6	Auto Choice 2	run auto mode 2
7	Broken 1	Intake/Cradle Sensors Broken	left most
8	Broken 2	Kicker Sensors Broken	.
9	Broken 3		.
10	Broken 4		.
11	Broken 5		.
12	Broken 6		Right most
X-axis	Manual Power	The amount of power for a manual shoot.	This is used when the Manual Shot button is pressed.
Y-axis	Future use	This is not used for anything at this time. But is available if needed.	silver knob (potentiometer)
Z-axis	Hip check buton	Make noise and flash the noise	0 When not pressed. 1 or higher is on.

SmartDashboard

Screen	Description (brief)	Operation	Notes	Variable Name	Data Type
Main	Camera Feed	This will be a direct feed from the camera.	The internet address will be based on the Team Number.	n/a	n/a
Main	Power meter	Meter next to the Camera Feed that shows the manual shooter's power. Would be a bar with a label next to it with a number representing power, scaling from 0 to 100		Manualpower	TBD
Setup Dialog (TBD)	Team Number	Numberbox	Sets the team number for the robot to set the camera feed. Should remain constant until we change the IP address of the robot. Should not change very much.	n/a	n/a