2011:Mechanical 1 2.12: Difference between revisions
From 1511Wookiee
Jump to navigationJump to search
(New page: = Attendance = '''Start time: ''' '''End time: ''' '''Members present: ''' '''Members Attending Next Meeting: ''' = Tasks Completed = *task **sub-task **sub-task *task = Tasks In Pr...) |
Mechanical1 (talk | contribs) No edit summary |
||
| Line 1: | Line 1: | ||
= Attendance = | = Attendance = | ||
'''Start time: ''' | '''Start time:''' | ||
'''End time: ''' | '''End time: 11:30 pm''' | ||
'''Members present: ''' | '''Members present: Notes from Tom Cav.''' | ||
'''Members Attending Next Meeting: ''' | '''Members Attending Next Meeting:''' | ||
= Tasks Completed = | = Tasks Completed = | ||
* | *On deployer - replace gas spring coupling with brass M6 x 1 insert. Fit end caps and slide. | ||
** | *Fab servo mounting bracket - need to make a print from detailed sketch notes left on table. | ||
** | *fitted steel wire spring to servo. On outside holes the servo is not strong enough to release latch | ||
*Initially had a couple of loops of wire to give it some compliance, but then bolted it solid, seems to work better. | |||
**Moved spring wire to inner hole pattern and seems to work OK under power. But takes two people to relatch. One to compress, and one to work the servo. Current spring wire is a little short. | |||
**My suggestion is to fab up a solid piece that would easily disconnect from the gate latch. So that latching can be done with gravity, then slide the arm linkage over the gate latch and use a spring pin to secure. | |||
*task | *task | ||
= Tasks In Progress = | = Tasks In Progress = | ||
*task | *task | ||
**sub-task | **sub-task | ||
**sub-task | **sub-task | ||
*task | *task | ||
= Tasks to Complete = | = Tasks to Complete = | ||
* | *I would continue to fit and adjust one of the gas spring end clevis bracket to get it more centered. Gas spring needs to be slightly lowered. The other side is fine. | ||
** | **We did look at mounting deployer slide but did not do much with it. | ||
** | **Just as a side note - the anchor bolts for the main frane in the corners - I think cap screw head should be to the inside so hex wrench fits easier, outside would be able to use wrench. | ||
* | **Will see you guys Sunday afternoon. | ||
= Materials Needed = | = Materials Needed = | ||
*task | *task | ||
**sub-task | **sub-task | ||
**sub-task | **sub-task | ||
*task | *task | ||
Latest revision as of 21:33, 12 February 2011
Attendance
Start time:
End time: 11:30 pm
Members present: Notes from Tom Cav.
Members Attending Next Meeting:
Tasks Completed
- On deployer - replace gas spring coupling with brass M6 x 1 insert. Fit end caps and slide.
- Fab servo mounting bracket - need to make a print from detailed sketch notes left on table.
- fitted steel wire spring to servo. On outside holes the servo is not strong enough to release latch
- Initially had a couple of loops of wire to give it some compliance, but then bolted it solid, seems to work better.
- Moved spring wire to inner hole pattern and seems to work OK under power. But takes two people to relatch. One to compress, and one to work the servo. Current spring wire is a little short.
- My suggestion is to fab up a solid piece that would easily disconnect from the gate latch. So that latching can be done with gravity, then slide the arm linkage over the gate latch and use a spring pin to secure.
- task
Tasks In Progress
- task
- sub-task
- sub-task
- task
Tasks to Complete
- I would continue to fit and adjust one of the gas spring end clevis bracket to get it more centered. Gas spring needs to be slightly lowered. The other side is fine.
- We did look at mounting deployer slide but did not do much with it.
- Just as a side note - the anchor bolts for the main frane in the corners - I think cap screw head should be to the inside so hex wrench fits easier, outside would be able to use wrench.
- Will see you guys Sunday afternoon.
Materials Needed
- task
- sub-task
- sub-task
- task
