2012:Robot IO Map
Type / Function | Channel |
Connected Device |
CAN ID Assignments |
0-127 |
|
RESERVED
|
01 | DO NOT USE. ID 1 is the factory-default CAN id; us not using it makes it easier to swap one in quickly and re-assign an id. |
|
02 | Left side drivetrain motor (front) |
|
03 | Left side drivetrain motor (rear) |
|
04 | Right side drivetrain motor (front) |
|
05 | Right side drivetrain motor (rear) |
|
06 | Shooter wheel motor (upper) |
|
07 |
Shooter wheel motor (lower) |
|
08 |
turret rotation motor |
|
09 |
Wing deployer motor |
|
10 |
|
|
11 |
|
|
12 |
|
|
13 |
|
|
14 |
|
|
15 |
|
|
16 |
|
PWM Outputs |
|
|
|
01 |
Camera Tilt servo |
|
02 |
RESERVED
Conveyor Stage 1 Sensor - LED power only |
|
03 |
RESERVED Conveyor Stage 2 Sensor - LED power only |
|
04 |
RESERVED
Conveyor Stage 3 Sensor - LED power only |
|
05 |
RESERVED
Conveyor Entrance Sensor - LED power only |
|
06 |
RESERVED Camera Light - LED power only |
|
07 |
|
|
08 |
|
|
09 |
|
|
10 |
|
Relay Outputs | ||
|
01 |
RESERVED (Possible Wings output) |
|
02 |
Beater Bar motor |
|
03 |
Conveyor Stage 1 motor |
|
04 |
Conveyor Stage 2 motor |
|
05 |
Conveyor Stage 3 motor |
|
06 |
Camera Light |
|
07 |
|
|
08 |
|
Analog Inputs |
||
|
01 |
Gyro |
B2 |
02 |
Conveyor Stage 1 High for Ball in conveyor Low when no ball present |
B3 |
03 |
Conveyor Stage 2 High for Ball in conveyor Low when no ball present |
B4 |
04 |
Conveyor Stage 3 High for Ball in conveyor Low when no ball present |
P1 |
05 |
Wing deployer position - potentiometer Higher values means closer to robot Lower values means more extended/closer to floor |
L3 | 06 |
Turret limit switch (optical OPB815WZ) - max CW High when limit is hit Low when limit is NOT hit |
|
07 | Turret limit switch (optical OPB815WZ) - max CCW
High when limit is hit Low when limit is NOT hit |
RESERVED |
08 |
Battery Voltage Input (Don't use for other devices) |
Digital IO (GPIO) | ||
IN - E1 |
01 |
Left drivetrain rotary encoder A |
IN - E1 | 02 |
Left drivetrain rotary encoder B |
IN - E2 |
03 |
Right drivetrain rotary encoder A |
IN - E2 |
04 |
Right drivetrain rotary encoder B |
IN - E3 |
05 |
Shooter upper wheel rotary encoder (E4P) |
IN - E4 |
06 |
Shooter lower wheel rotary encoder (E4P) |
IN - E5/E6 | 07 |
Turret motor shaft - rotary encoder (E4P) or turret sprocket position - opto-reflective rotary encoder |
IN - B1 |
08 |
conveyor stage 1 entrance - beam break sensor (homemade, 1" cube) High for Ball in conveyor Low when no ball present |
OUT | 09 |
LED - Red |
OUT | 10 |
LED - Green |
OUT | 11 |
LED - Blue |
OUT | 12 |
LED Strip 1 - Select |
OUT | 13 |
LED Strip 2 - Select |
OUT | 14 |
LED Strip 3 - Select |
Pneumatics Bumper | ||
01 | ||
02 | ||
03 |