2015:Electrical Main: Difference between revisions

From 1511Wookiee
Jump to navigationJump to search
No edit summary
No edit summary
 
(44 intermediate revisions by 4 users not shown)
Line 1: Line 1:
= Important Stuff =
= IO Interface Map =


[[2015:Robot IO Map]]
[[2015:Robot IO Map]]


----
----


= Sensors =
= Sensors =
Line 9: Line 11:
<span style="font-size:x-large;"><span style="font-size:large;">Drive Base:</span></span>
<span style="font-size:x-large;"><span style="font-size:large;">Drive Base:</span></span>


*<span style="font-size:x-large;"><span style="font-size:large;"><span style="font-size:small;"><span style="font-size:medium;">two encoders</span></span></span></span>
*<span style="font-size:x-large;"><span style="font-size:large;"><span style="font-size:small;"><span style="font-size:medium;">two encoders (left and right)</span></span></span></span>
*<span style="font-size:x-large;"><span style="font-size:large;"><span style="font-size:small;"><span style="font-size:medium;">one channel for each encoder</span></span></span></span>
*<span style="font-size:x-large;"><span style="font-size:large;"><span style="font-size:small;"><span style="font-size:medium;">two&nbsp;channels for each encoder</span></span></span></span>
*<span style="font-size:x-large;"><span style="font-size:large;"><span style="font-size:small;"><span style="font-size:medium;">one gyro</span></span></span></span>
*<font size="3"><span style="line-height: 28.444446563720703px;">gyro and accelerometer compound board (am-2067, containing&nbsp;ADXL245 &&nbsp;ADW22307)</span></font>
*<span style="font-size:x-large;"><span style="font-size:large;"><span style="font-size:small;"><span style="font-size:medium;">Need to use strafing in autonomous</span></span></span></span><span style="font-size:x-large;"><span style="font-size:large;"><span style="font-size:small;"><span style="font-size:medium;">​!</span></span></span></span>
*<span style="font-size:x-large;"><span style="font-size:large;"><span style="font-size:small;"><span style="font-size:medium;">Need to use strafing in autonomous</span></span></span></span><span style="font-size:x-large;"><span style="font-size:large;"><span style="font-size:small;"><span style="font-size:medium;">​!</span></span></span></span>
*<span style="font-size:x-large;"><span style="font-size:large;"><span style="font-size:small;"><span style="font-size:medium;">2-speed shifter (pneumatic)</span></span></span></span>


<span style="font-size:x-large;"><span style="font-size:large;"><span style="font-size:small;"><span style="font-size:medium;">​<span style="font-size:large;">Lifter:</span></span></span></span></span>
<span style="font-size:x-large;"><span style="font-size:large;"><span style="font-size:small;"><span style="font-size:medium;">​<span style="font-size:large;">Lifter:</span></span></span></span></span>


*<span style="font-size:medium;">flag sensor for calibration</span>
*<span style="font-size:medium;">flag sensor at bottom/home for calibration</span>
*<span style="font-size:medium;">flag sensor at&nbsp;highest extent</span>
*<font size="3"><span style="line-height: 28.444446563720703px;">63R256 encoder for interpolation between top/bottom</span></font>
*<span style="font-size:medium;">do we need hard stops?</span>
*<span style="font-size:medium;">do we need hard stops?</span>
*<span style="font-size:medium;">lifter needs to be physically removed</span>
*<span style="font-size:medium;">lifter needs to be physically removed</span>
*<span style="font-size:medium;">motor (2)(775)</span>
*<span style="font-size:medium;">2 RS775-18 motors</span>
*<span style="font-size:medium;">1 Camera (Stationary)</span>
*<span style="font-size:medium;">bike brake with pneumatic actuation (double acting cylinder, single solenoid)</span>


<span style="font-size:medium;">​<span style="font-size:large;">Gripper:</span></span>
<span style="font-size:medium;">​<span style="font-size:large;">Gripper:</span></span>


*<span style="font-size:medium;"><span style="font-size:large;"><span style="font-size:medium;">encoder on one</span></span></span>
*<span style="font-size: medium; line-height: 28.444446563720703px;">63R256&nbsp;</span><span style="font-size:medium;"><span style="font-size:large;"><span style="font-size:medium;">encoder after gearbox output</span></span></span>
*<span style="font-size:medium;">flag sensor</span>
*<span style="font-size:medium;">flag sensor for inner home position</span>
*<span style="font-size:medium;">the motor is a 550</span>
*<span style="font-size:medium;">the motor is a&nbsp;RS550</span>
*<span style="font-size:medium;">2 ultrasonic sensors for landfill</span>
*<span style="font-size:medium;">1&nbsp;banner sensors out on grippers for tote acquisition</span>
*<span style="font-size:medium;">Banner sensor for wide tote config</span>
*<span style="font-size:medium;">Flag (?) sensor for wide tote config</span>
 
<span style="font-size:medium;"><span style="font-size:large;">​Stabilizer:</span></span>
 
*<span style="font-size:medium;"><span style="font-size:large;"><span style="font-size:medium;">pneumatic on/off (single solenoid, dual acting cylinder)</span></span></span>
 
== Interface Circuits ==
 
=== <u>Banner Photodetector Sensors:</u> ===
 
*Q10 Series (Q10AN6R Detector)
**Sensor is NPN open-collector output
**Sensor off-state leakage is 10uA max.
**Sensor on-state logic low is 0.5V max @ 10mA max
*RoboRIO DIO [0..9]
**Have internal 40K pullup resistors to +3.3Vdc
**RoboRIO DIO VIL=0.8V max
**RoboRIO DIO VIH=2.0V&nbsp;min.
*Interface Circuit
**Sensor off-state leakage of 10uA through RoboRIO pullup of 40K drops 0.4V, so logic high is 3.3V - 0.4V = 2.9V
**Logic high is safely above RoboRIO VIHmin of 2.0V
**Sensor on-state logic low of 0.5V is safely below RoboRIO VILmax of 0.8V.
**The current that the sensor must sink is (3.3V - 0.5V) / 40Kohms = 70uA, which is well below the max sinking capability of the sensor of 10mA.
**So no external interface circuit is required - the Banner Sensor detector of this type (NPN O.C.) may be wired directly to the RoboRIO DIO.
**If desired, however, a lower resistance pullup could be added to lower the impedance of the interface, which might help reduce susceptibility to electrical interference. &nbsp;(minimum value of pullup approx. 2.7Kohms to still give good margin for logic low condition, with&nbsp;1mA current sink.)
 
== Wire Bundle to Gripper Notes ==
 
IN CHANNEL WIRES
 
1 RS 550 Motor - 2-wire, 10/12 AWG
 
1 Encoder both phases - 4-wire (5V, GND, ENC-A, ENC-B)&nbsp;20-22 AWG
 
2 Flag sensors - 2 shared wire for emitter, 1 wire ground share for detector, 1 wire each for detector signal
 
  TOTAL = 5 wires, 20-22 AWG
 
1 Banner sensor - 2 wire 12V for emitter & collector - 1 wire for detector signal - 20-22 AWG
 
  TOTAL = 3 wire
 
 
'''Cable Colors to Box Colors:''' White Orange - Blue&nbsp;
 
Orange - Orange
 
White Green - Black
 
Blue - Red
 
White Blue - Green
 
Green - Yellow
 
White Brown - Brown
 
Brown - White
 
 
'''Box to Box Connection (Split Ethernet)'''
 
<u>Functions:</u>
 
1) Encoder Phase
 
2) 5V
 
3) GND
 
4) 12V
 
5) Flag Left (secondary)
 
6) Flag Right (primary)
 
7) Encoder Phase
 
8) NC
 
 
 
<u>Colors:</u>
 
1) White Brown
 
2) Orange
 
3) White orange
 
4) White blue
 
5) White Green
 
6) Brown
 
7) Blue
 
8) Green
 
 
'''Signal/Power to Box Mapping:''' Black - Ground
 
Red - 12V
 
Orange - 5V
 
Blue - Banner Sensor Detector Signal
 
Green - Encoder A
 
Yellow - Encoder B
 
Brown - Gripper Flag Primary
 
White - Gripper Flag Secondary


<span style="font-size:medium;"><span style="font-size:large;">​Stabilization:</span></span>
<br/>10/12 AWG


*<span style="font-size:medium;"><span style="font-size:large;"><span style="font-size:medium;">pneumatic on/off</span></span></span>
+/- 12V for motor
 
<br/>9 -- 20/22 AWG (8 if common GND for all sensors) 5V Digital GND
 
Enc PA, Enc PB
 
12V for flag sensors (Robot2 used 5V for flag sensors), PD GND
 
3 Detector signals
 
*PD GND and Digital GND the same
 
= Robot Indicators =
 
*Lift Position
**"Bar Graph" style display on LED panel
**Adressable type LED strips so that can be turned on/off individually
*Gripper Open Width&nbsp;
**"Bar Graph" style display from the center on LED panel
**Addressable type LED strips so that can be turned on/off individually
**When gripper Banner sensor is tripped (tote within grippers), LEDS change color
*Other Functions
**LED strips at top of lift on front and back (just below cameras)
**Indicate drive shifter&nbsp;high gear or low gear
**Indicate strafing wheel down
*LED Strip driver requirements
**30LED/m strip is 2A/m (9.5W)
**60LED/m strip is 3.6A/m (18W) - preferred for high resolution "bar graph" display
**Estimated total LED strip length for robot is 2.5m
**Total 5Vdc current requirement for 60LED/m is 10.8A for 3m
**12v to 5v converter from previous year's robots (used for wireless gateway) can do 5A.


= Component Specifications =
= Component Specifications =


[[File:Talon-SRX-Info-Sheet.pdf|Talon SRX Data Sheet]]
[[File:Talon-SRX-Info-Sheet.pdf|Talon SRX Data Sheet]]
[[File:RoboRIO User Manual.pdf|RoboRio Manual]]
[[File:RoboRIOspecifications.pdf|RoboRIO specs]]
[[File:PCM-Users-Guide.pdf|Pneumatics Control Module]]
[[File:VRM User Guide.pdf|Voltage Regulator Module]]
[[File:RevRoboticsMoreBoard.pdf|Rev Robotics RoboRIO Expansion Board]]
[[File:Atmel_ATmega32U4.pdf|Arduino processor data sheet]]


[[File:2013 Motor Data Table.xls|2013 Motor Data]]
[[File:2013 Motor Data Table.xls|2013 Motor Data]]


[[File:2013 MotorCurves.xls|2013 Motor Performance Curves]]
[[File:2013 MotorCurves.xls|2013 Motor Performance Curves]]
[[File:2015 Motor Information.pdf|2015 Motor Data]]


[[Sensors]]
[[Sensors]]


[[Servos|Servos]]
[[Servos|Servos]]
[[LED Strips]]


[[Micro Switches]]
[[Micro Switches]]
Line 56: Line 224:


[https://wpilib.screenstepslive.com/s/4485/m/24166/l/144972-status-light-quick-reference Electrical Indicators Reference Link]
[https://wpilib.screenstepslive.com/s/4485/m/24166/l/144972-status-light-quick-reference Electrical Indicators Reference Link]
= IO Maps for Old Robots =
*[[2014:Robot IO Map|2014 IO Map]]
*[[2013:Robot IO Map|2013 IO Map]]
*[[2012:Robot IO Map|2012 IO Map]]
*[[2011:Robot IO Map|2011 Thunderous Prime IO Map]]
*[[2010:Electrical Main#IO Map 2010 Thunderfoot|2010 Thunderfoot IO Map]]
*[[2009:IO Map|2009 Thunderplucker]]
*[[IO Pin Maps for Pre-2009 Robots]]


= Archives =
= Archives =
Line 75: Line 233:
*[[2010:Electrical Main|2010 Electrical Main]]
*[[2010:Electrical Main|2010 Electrical Main]]
*[[2009:Electrical Main|2009 Electrical Main]]
*[[2009:Electrical Main|2009 Electrical Main]]
[[Category:Pages with broken file links]]

Latest revision as of 13:31, 1 March 2015

IO Interface Map

2015:Robot IO Map


Sensors

Drive Base:

  • two encoders (left and right)
  • two channels for each encoder
  • gyro and accelerometer compound board (am-2067, containing ADXL245 & ADW22307)
  • Need to use strafing in autonomous​!
  • 2-speed shifter (pneumatic)

​Lifter:

  • flag sensor at bottom/home for calibration
  • flag sensor at highest extent
  • 63R256 encoder for interpolation between top/bottom
  • do we need hard stops?
  • lifter needs to be physically removed
  • 2 RS775-18 motors
  • 1 Camera (Stationary)
  • bike brake with pneumatic actuation (double acting cylinder, single solenoid)

​Gripper:

  • 63R256 encoder after gearbox output
  • flag sensor for inner home position
  • the motor is a RS550
  • 1 banner sensors out on grippers for tote acquisition
  • Flag (?) sensor for wide tote config

​Stabilizer:

  • pneumatic on/off (single solenoid, dual acting cylinder)

Interface Circuits

  • Q10 Series (Q10AN6R Detector)
    • Sensor is NPN open-collector output
    • Sensor off-state leakage is 10uA max.
    • Sensor on-state logic low is 0.5V max @ 10mA max
  • RoboRIO DIO [0..9]
    • Have internal 40K pullup resistors to +3.3Vdc
    • RoboRIO DIO VIL=0.8V max
    • RoboRIO DIO VIH=2.0V min.
  • Interface Circuit
    • Sensor off-state leakage of 10uA through RoboRIO pullup of 40K drops 0.4V, so logic high is 3.3V - 0.4V = 2.9V
    • Logic high is safely above RoboRIO VIHmin of 2.0V
    • Sensor on-state logic low of 0.5V is safely below RoboRIO VILmax of 0.8V.
    • The current that the sensor must sink is (3.3V - 0.5V) / 40Kohms = 70uA, which is well below the max sinking capability of the sensor of 10mA.
    • So no external interface circuit is required - the Banner Sensor detector of this type (NPN O.C.) may be wired directly to the RoboRIO DIO.
    • If desired, however, a lower resistance pullup could be added to lower the impedance of the interface, which might help reduce susceptibility to electrical interference.  (minimum value of pullup approx. 2.7Kohms to still give good margin for logic low condition, with 1mA current sink.)

Wire Bundle to Gripper Notes

IN CHANNEL WIRES

1 RS 550 Motor - 2-wire, 10/12 AWG

1 Encoder both phases - 4-wire (5V, GND, ENC-A, ENC-B) 20-22 AWG

2 Flag sensors - 2 shared wire for emitter, 1 wire ground share for detector, 1 wire each for detector signal 

  TOTAL = 5 wires, 20-22 AWG

1 Banner sensor - 2 wire 12V for emitter & collector - 1 wire for detector signal - 20-22 AWG 

  TOTAL = 3 wire


Cable Colors to Box Colors: White Orange - Blue 

Orange - Orange

White Green - Black

Blue - Red

White Blue - Green

Green - Yellow

White Brown - Brown

Brown - White


Box to Box Connection (Split Ethernet)

Functions:

1) Encoder Phase

2) 5V

3) GND

4) 12V

5) Flag Left (secondary)

6) Flag Right (primary)

7) Encoder Phase

8) NC


Colors:

1) White Brown

2) Orange

3) White orange

4) White blue

5) White Green

6) Brown

7) Blue

8) Green


Signal/Power to Box Mapping: Black - Ground

Red - 12V

Orange - 5V

Blue - Banner Sensor Detector Signal

Green - Encoder A

Yellow - Encoder B

Brown - Gripper Flag Primary

White - Gripper Flag Secondary


10/12 AWG

+/- 12V for motor


9 -- 20/22 AWG (8 if common GND for all sensors) 5V Digital GND

Enc PA, Enc PB

12V for flag sensors (Robot2 used 5V for flag sensors), PD GND

3 Detector signals

  • PD GND and Digital GND the same

Robot Indicators

  • Lift Position
    • "Bar Graph" style display on LED panel
    • Adressable type LED strips so that can be turned on/off individually
  • Gripper Open Width 
    • "Bar Graph" style display from the center on LED panel
    • Addressable type LED strips so that can be turned on/off individually
    • When gripper Banner sensor is tripped (tote within grippers), LEDS change color
  • Other Functions
    • LED strips at top of lift on front and back (just below cameras)
    • Indicate drive shifter high gear or low gear
    • Indicate strafing wheel down
  • LED Strip driver requirements
    • 30LED/m strip is 2A/m (9.5W)
    • 60LED/m strip is 3.6A/m (18W) - preferred for high resolution "bar graph" display
    • Estimated total LED strip length for robot is 2.5m
    • Total 5Vdc current requirement for 60LED/m is 10.8A for 3m
    • 12v to 5v converter from previous year's robots (used for wireless gateway) can do 5A.

Component Specifications

File:Talon-SRX-Info-Sheet.pdf

File:RoboRIO User Manual.pdf

File:RoboRIOspecifications.pdf

File:PCM-Users-Guide.pdf

File:VRM User Guide.pdf

File:RevRoboticsMoreBoard.pdf

File:Atmel ATmega32U4.pdf

File:2013 Motor Data Table.xls

File:2013 MotorCurves.xls

File:2015 Motor Information.pdf

Sensors

Servos

LED Strips

Micro Switches

Electrical Inventory

File:MX5 CircuitBreaker.pdf

File:VB3 CircuitBreaker.pdf

US Digital Encoders Link

Electrical Indicators Reference Link

Archives

Retrieved from "https://wiki.penfieldrobotics.com/wiki/index.php?title=2015:Electrical_Main&oldid=7849"