Fabrication

How to Submit Parts

    In order to get parts made a drawing must be completed and the appropriate files must be submitted (see below for drawing and file requirements).  Please create a new link on this page (under files to be made) for each part request and include the proper drawing and required files.  Any questions at all, please ask Amy Gontarek (agontare@harris.com) 

    Drawing Requirements: (use the FIRST/Robotics drawing template under the English tab on the template menu).  Save a Copy As .dwg as Autocad LT.

                  List Material

                  State Quantity

                  Provide Overall Dimensions

                  Name of student who created the drawing

                  Current Date - this needs to be updated everytime a drawing is submitted to get parts made (this acts as the revision control)

                  *  If it is a sheet metal part to be bent, then the bend radius must be dimensioned along with the feature

                  * If the part will be welded, then care must be taken to design with the proper dimensioning scheme leaving room for the weldments

   File Requirements:

                 - Machined Parts (think parts with intricate surfaces) - .stp  

                 - OMAX Parts (think flat parts, bar stock to be cut to length) - .dxf

                                This is basically a stripped down version of the drawing.  It should include the face on view of the part (no other views) with no dimensions and should be scaled 1:1 and then use Save a Copy As and save as a .dxf Autocad LT.

Files to be made

Date	Requested Item	Requestor	Ordered By/Date	QTY	RX'd
2/3/09	trap door end	Cuyler McC		10	IKE
2/3/09	shaft 750.idw	Cuyler McC	DXF mailed to Kim and given hard copy 2/3	8	IKE shop

 

 

 

NOTE:

2/3 - LEFT AND RIGHT FRAMES, WAITING FOR 1 X 1 SQUARE TUBING STOCK TO ARRIVE AT HARRIS SO FRAMES
CAN BE WELDED.  ACCORDING TO AMY, STOCK MIGHT BE ON SHIPPING DOCK.  SHE WILL CHECK TOMORROW MORNING.

MOST OTHER PARTS AT HARRIS ARE DONE AND AT HER DESK WAITING FOR WELDING.  Raw stock received 2/4/09. 

Order Status

Date	Requested Item	Requestor	Ordered By/Date	QTY	RX'd
1/16/09	mount_bumper	Josh Gannon	Gontarek - 1/16/09	10 - dxf	1/20/09
1/23/09	gusset upper	Alex Wolf	Gontarek 1/23/09	4 -dxf	1/26/09
1/23/09	1.75 ball bearing block	Alex Wolf	Gontarek 1/23/09	2 - dxf	1/26/09
1/23/09	ball bearing block tall	Alex Wolf	Gontarek 1/23/09	2 - dxf	1/26/09
1/23/09	ball bearing block	Alex Wolf	Gontarek 1/23/09	14 - dxf	1/26/09
1/23/09	pulley block (bearing block mount) resubmitted 1/27/09 for holes	Alex Wolf	Gontarek 1/23/09	14 - dxf	1/28/09
1/23/09	gusset	Alex Wolf	Gontarek 1/23/09	4 -dxf	1/26/09
1/23/09	ball bearing block mid (bearing block mid 2)	Alex Wolf	Gontarek 1/23/09	2 - dxf	1/26/09
1/23/09	double pulley (ordered near net shape - Harris)	Alex Wolf	Gontarek 2/2/09	12 - dxf	2/3/09
1/23/09	single pulley (ordered near net shape - Harris)	Alew Wolf	Gontarek 2/2/09	16 - dxf	2/3/09
1/26/09	span foot	Alex Wolf	Gontarek 1/26/09	2 - dxf	1/28/09
1/26/09	right ND motor mount	Alex Wolf	Gontarek 1/26/09	1 - dxf	1/28/09
1/26/09	cross member tie plate 1x1	Alex Wolf	Gontarek 1/26/09	8 - dxf	1/28/09
1/26/09	conveyor drive motor mounting plate	Alex Wolf	Gontarek 1/26/09	3 - dxf	1/28/09
1/28/09	angle bracket	Alex Wolf	Gontarek 1/28/09	2 - dxf	1/30/09
1/29/09	cross member thread plug	Alex Wolf	Gontarek 1/29/09	14 - dxf	1/30/09
1/29/09	flip box (controls)	Eric Averill	Gontarek 1/29/09	1- dxf/weld	2/3/09
1/30/09	front door base	Alex Wolfe	Gontarek 1/30/09	1 - dxf	2/2/09
1/26/09	conveyor drive motor mount clamp	Alex Wolf	Gontarek 1/26/09 DXF mailed to Kim and given hard copy 2/3	3 - stp	IKE shop
	single pulley	Alex Wolfe	Blanks from Harris at PHS, DXF mailed to Kim and given hard copy2/3	16	IKE shop
	double pulley	Alex Wolfe	Blanks from Harris at PHS, DXF mailed to Kim and given hard copy2/3	12	IKE shop
2/3/09	Top Bracket	Dean Smith	Gontarek 2/4/09	10
2/3/09	Drawer Bracket	Dean Smith	Gontarek 2/4/09	6
2/3/09	Bottom Plate	Dean Smith	Gontarek 2/4/09	1	IKE shop?
2/3/09	Frame Cross Tie Weldment 2	Cuyler McChesney	Gontarek 2/4/09 Raw stock from PHS- parts to be welded	1
2/3/09	Frame Cross Tie Weldment 1	Cuyler McChesney	Gontarek 2/4/09 Raw stock from PHS - parts to be welded	4
2/3/09	Trap Door End		DXF mailed to Kim and given hard copy 2/3
2/3/09	Rear Coupling Aluminum Screw Lock		On assembly, no drawing made for it. Kyler working on it 2/4 2.5 Dia, x 1/2 thk with a bunch of taped holes	1	?

Media:Parts_1-11-2009.xls

 

 

 

 

 

 

 

 

<u</u>

<u</u>

<u</u>

<u</u>

Parts Built Elsewhere

Date	Part Name	Where to Make	Builder/Date	QTY	RX'd
2/3/09	helper finger	In House	On Job Shelf	4	done
2/3/09	banner sensor mounting plate.idw	In House	On Job Shelf to mill slots	2	inproc.
2/3/09	banner sensor mount.idw	In House	On Job Shelf to mill slots	2	inproc.
2/3/09	Frame Outrigger SubAssembly - Right Side.idw	In House	On Job Shelf	1	done
2/3/09	Frame Outrigger SubAssembly - Left Side.idw	In House	On Job Shelf	1	done
2/3/09	front door weldment.idw	In House	On Job Shelf	1	done
2/3/09	Lower crank.idw	In House	On Job Shelf	1	done
2/3/09	Upper crank.idw	In House	On Job Shelf stock cut	1	inproc.
2/3/09	modAndyMarkhub.idw	In House	On Job Shelf	1	done
2/3/09	joint rod 1	In House	On Job Shelf	1	done
2/3/09	joint rod 2	In House	On Job Shelf	1	done
2/3/09	Banner Photo Eye Mounting Stand-Offs	In House	no drawing yet Basically a thick washer	2	not Started
2/4/09	30" Shaft (Trap Door Pivot Shafts)	In House	Drawing done 2/4.  Drawing on job shelf	2	not Started
2/4/09	Upper Plucker Motor Mount Plate	In House	Drawing done 2/4. Drawing on job shelf	1	not Started
2/4/09	Gear Coupling AL Lock	In House	Need to finsh drawing and check. Drawing on job shelf for cutting stock only	1	not Started