Fabrication

How to Submit Parts

    In order to get parts made a drawing must be completed and the appropriate files must be submitted (see below for drawing and file requirements).  Please create a new link on this page (under files to be made) for each part request and include the proper drawing and required files.  Any questions at all, please ask Amy Averill.

                                                    Notice that to save in any of these formats, you must click on "Save Copy As".

---

Once your part is complete, create a new drawing for your part (.idw):    

   Drawing Requirements: (use the FIRST/Robotics drawing template under the English tab on the template menu).

The objective of the drawing is to show the main views of the part (front, right, left, top, bottom) and to provide dimensions so that someone can easily understand what the part is supposed to look like.  The drawing should also: 

                  -  List Material

                  -  State Quantity Required

                  -  Provide Overall Dimensions - length, width, height ( * if the part is a sheetmetal part that is bent, then the dimensions must also include the location

                     of the bends and the radius used to bend the part)

                  -  Note if any hardware needs to be installed and on which surface (such as standoffs or inserts - PEMS)

                  -  Name of student who created the drawing

                  -  Current Date - this needs to be updated everytime a drawing is submitted to get parts made (this acts as the revision control)

          

                  * If the part will be welded, then care must be taken to design with the proper dimensioning scheme leaving room for the weldments

Once the drawing is complete, go to Save a Copy ---> Save a Copy As AUTOCAD .dwg (Autocad LT.)

SAMPLE DRAWING

'Additional' File 'Requirements:'  Besides the drawing there are additional files that need to be created in order to store the actual data of the part.  Determine if your part is a machined part or cut part and then create the necessary file as listed below. 

                  - If the part is a machined part (think parts made from blocks of aluminum with intricate surfaces) then a .stp file needs to be created

                             To create a .stp

                             - Have the part model open (.ipt), go to Save a Copy ---> Save a Copy As ---> Choose file format .stp 

                 - If the part is a cut part (think flat parts with holes, bar stock to be cut to length, sheetmetal that gets bent) then a .dxf  file needs to be created.  The .dxf

                   is basically a stripped down version of the drawing.

                             To create a .dxf

                             *  If the part is bent start by changing the model (.ipt) to the flat pattern (unbent version) before creating the new drawing (.idw).  When the top

                              view is shown it should be 'in the unbent state

                             - Create a new drawing (.idw) for the part.  Show the top view of the part (with all the cutouts, holes, if there are any)

                             - There should be no borders or templates

                             - There should be no dimensions

                             - Scale the part 1:1

                             - Then use Save a Copy---> Save a Copy As and save as a .dxf Autocad LT.

Files to be made

Date	Requested Item	Requestor	Ordered By/Date	QTY	RX'd
1/31/10	1 - 01	Richards		1
1/31/10	1 - 02	Richards		1
1/31/10	1 - 03	Richards		1

Order Status

Date	Requested Item	Requestor	Ordered By/Date	QTY	RX'd
1/13/10	2010 Slot Chassis Brkt	Gannon	Averill 1/13/10	8	1/15
1/13/10	2010 Motor Mount SS	Gannon	Averill 1/13/10	4	1/15
1/13/10	2010 Rear Moto Cross Brace	Gannon	Averill 1/13/10	1	1/15
1/13/10	2010 Bearing Block 3_8ID	Gannon	Averill 1/14/10	4	1/18
1/15/10	2010 Camera Mount Sheet 1	Dora	Averill 1/14/10	1	1/18
1/18/10	2010 Camera Mount Bent	Dora	Averill 1/14/10	1	1/18
2/1/10	Control Box Insert	Controls	Averill 2/1/10	1	2/2

Parts Built Elsewhere

Date	Part Name	Where to Make	Builder/Date	QTY	RX'd

Archives

• 2009 Fabrication Page