Latest revision as of 15:23, 25 February 2026

Overall Concept

Physical Box:

Design Idea: Satchel

Mock Up of Lid 'latch', using magnets (this worked well)

Stitching/Stamping

Design Info

Paint Scheme: Brown, Brass, Black

P073 Controls Bottom: Brown
P074 Controls Top: Brown
P075 Angle - Rolling: Brown
P076 Angle - LCD: Brown
P077 Angle - Thunder: Brown
P078 Angle - Magnets: Brown
P079 Angle - Tiny: Brown
P080 Laptop Holder: Black
P081 Power and Ethernet: Brown
P082 Controller Holder: Black ABS
P083 Controller Holder 2: Black ABS
P111 Controls Handle: Red Filament, Painted Black

Overall Dimension: 23" by 13.75" without handle

Patch Dimension: 2" by 3" with 0.2" Rivets

Leather is 2.0 MM Thick

1511 stamp (0.17"H by 0.366"W)

Lightning Bolt stamp (1.5" by 2.5")

Websites:

fontspace.com: Dinosaur Font #1
fontspace.com: Dinosaur Font #2
fontspace.com: Dinosaur Font #3
fontspace.com: Dinosaur Font #4
youtube.com: How to Stamp Leather
lego.com: LEGO Bone
amazon.com: Handle Option #1
amazon.com: Strap Option #1
Strap Option #2
LCD:
- touch LCD 4"
- spec for above
- another LCD
- knockoff Mega 2560
- Arduino Mega 2560
- Capacitive Touch <- using this one for 2026, with a Arduino Nano Every
  - specs for above LCD
Thingaverse Bones:
amazon.com: Rivets
amazon.com: Rivets 2.0
amazon.com: Buckle
Bag Pouch/Handle

LCD Layout

To - Do

Sami:

Tool Test (100%) & Game Test (100%)
Used the Mill for the FIRST TIME 2/21/2026

Clara:

Tool Test (100%) & Game Test (>80%/passed)
Artist (R - T - EAST)

Not Started

Label Broken Switches
Final mounting of the LCD.

In Progress

LCD Stuff

Completed

Design

Added design pictures to the "Overall Concept" and the "Design Info" section
Added links for fonts, videos, and bling to the "Design Info" section
Brought over 2025 files to 2026: Laptop holder, Controller holder, Ethernet, Bottom, Lid, Controller, Laptop, Magnet
Finalized design concept
Magnet mock up (lid)
Determined overall size (23" by 13.75" without handle)
Added leather, magnets, sliding tape, power strip, handle, rivets, buckle strap, bag, LCD, LEDs, broken switches, power plug, Right Angle Ethernet, SD Card to shopping list
Determined that latch is bling only and not functional
Researched Thingaverse bones for 3-D printing
Created a to scale lid on paper
Found HUB, A to B USB Cable, USB for Arduino, Right Angle USB, PCB Board, Spade Connectors

CAD

Fixed the 'G' in Rolling Thunder
Added dinosaur footprints into bottom end
Look at end
Added holes for magnets and studs in the top
Added holes for angle supports; in supports and bottom
LCD: opening in bottom and PEM holes for mounting
Finished remaining fillets on letters
Added notches to angle pieces (so we can bend down later to help with lid insertion)
Changed mounting holes on laptop holder to correct size
Updated CAD for new controller holder mounting (NOTE: two holes in bottom do NOT get PEMS, like last year, see mini assembly)
Changed 'DIVE' to '1511' on laptop holder (just for now, incase we don't have time to work on it)
Assigned part numbers for all our items and updated the names in Onshape to match
controller holders
LCD opening and studs
Created a 1511 stamp (0.17"H by 0.366"W)
Created a lightning bolt stamp (1.5" by 2.5")
Bottom: printed 2 copies of PDF and put in binder
Power & Ethernet: printed 2 copies of PDF and put in binder
Top: created drawing and approved, created flat pattern DXF and PDF, printed 2 copies of PDF and put in binder, posted DXF and PDF to Teams
Changed one '1511' to a bone in the Laptop Holder
Laptop Holder: created drawing and got approved, created a flat pattern DXF, PDF and STEP , posted DXF, PDF, STEP to teams, printed 2 copies of PDF and put in binder
Angle - Tiny: created drawing and got approved, created a flat pattern DXF and PDF, posted DXF and PDF to teams, printed 2 copies of PDF and put in binder
Angle - Rolling: created drawing and got approved, created a flat pattern DXF and PDF, posted DXF and PDF to teams, printed 2 copies of PDF and put in binder
Angle - LCD: created drawing and got approved, created a flat pattern DXF and PDF, posted DXF and PDF to teams, printed 2 copies of PDF and put in binder
Angle - Thunder: created drawing and got approved, created a flat pattern DXF and PDF, posted DXF and PDF to teams, printed 2 copies of PDF and put in binder
Angle - Magnets: created drawing and got approved, created a flat pattern DXF and PDF, posted DXF and PDF to teams, printed 2 copies of PDF and put in binder
Controller Holder: created drawing and got approved, printed 2 copies and put in binder, created STL and put in teams, updated parts and assembly log and 3D printed parts request
Controller Holder 2 : created drawing and got approved, printed 2 copies and put in binder, created STL and put in teams, updated parts and assembly log and 3D printed parts request
Control Handle: created drawing and got approved, printed 2 copies and put in the binder, created STL and put it in teams, updated parts and assembly log and 3D printed parts request
LCD Cage: created drawing and got approved, created STL and put in teams, updated parts and assembly log and 3D printed parts request

CAD Assembly

Constrained magnets in assembly and notched end angle support
Created mini CAD assemblies, because we will need those for Harris Shop; included PEMs
Confirmed steel for magnets on top will clear end
Determined controller holder placement and mounting

Shop Drawings

Created drawings for Bottom and Power/Ethernet
Created a STEP oof Bottom

Test Fitting

Test fitted rivets

Final Assembly

Stamped/Etched Leather Pieces
Finalized Paint Scheme
Handle
Cable Management
Put in and tested magnets

Wiring

Modified Broken Switches with Spade Connectors and tested
Removed Cap from 2023 PCB Board
Soldered LCD & Arduino headers onto PCB Board
Made diagram

Meeting Minutes

1/10 (Sat)

Attendees: Sami, Clara, Byers, Eric

Work Completed:

Design concepts

1/11 (Sun)

Attendees: Sami, Byers

Work Completed:

Design concepts

1/14 (Wed)

Attendees: Sami, Clara, Byers

Work Completed:

Added dinosaur font links to "Design Info" section
Added a YouTube link about how to stamp leather into the "Design Info" section
Added a picture of a stamp handle for an example into the "Design Info" section
Added a lego.com link for LEGO Bones to the "Design Info" section - Determined (if decided to use) 8 needed, purchase 10
Started bringing over files (2025 to 2026): Laptop holder, Controller holder, Ethernet, Bottom, Lid, Controller, Laptop, Magnet

1/17 (Sat)

Attendees: Sami, Clara, Matias, Byers

Work Completed:

Finalized design concept
Magnet mock up (lid)
Brought over files from 2025 to 2026: Laptop holder, Controller holder, Ethernet, Bottom, Lid, Controller, Laptop, Magnet (NOTE: final assembly needs constraints re-done)
Researched handles/straps

1/18 (Sun)

Attendees: Sami, Byers, Eric

Work Completed:

Started CAD
Determined overall size (23" by 13.75" without handle)
Created sizing for stamps
Added leather, magnets, sliding tape, and power strip on shopping list
Researched LCDs and Arduinos

1/21 (Wed)

Attendees: Sami, Clara, Eric

Work Completed:

Determined that latch is bling only and not functional
Designed handle for lid... its a bag... (see updated picture)
Figured out how to flange!!!
Researched Thingaverse bones for 3-D printing
Researched handle, rivets, clasp

1/22 (Thu)

Attendees: Sami, Clara, Byers

Work Completed:

Change font for Rolling Thunder
Determined offset of lid supports (aka Angle pieces) to top lip & fixed constraints
adjusted lid support lengths and how much it goes into the box
fixed laptop constraints in assembly
Researched bags

1/24 (Sat) V-CARVE WITH PIZZO

Attendees: Sami, Clara, Byers, Eric

Work Completed:

Added handle, rivets, buckle strap, and bag to shopping list
Fixed the 'G' in Rolling Thunder
Added dinosaur footprints into bottom end
Created a to scale lid on paper
CAD: added holes for magnets and studs in the top
CAD: constrained magnets in assembly and notched end angle support
CAD: did holes for angle supports; in supports and bottom

1/25 (Sun)

Attendees: Byers, Eric

Work Completed:

Created mini CAD assemblies, because we will need those for Harris Shop; included PEMs
picked LCD and put on shopping list
CAD: LCD, opening in bottom and PEM holes for mounting (NOTE: will create 'cage' around LCD)
confirmed steel for magnets on top will clear end
finished remaining fillets on letters
added notches to angle pieces, so we can bend down later to help with lid insertion
made laptop holder mounting holes slightly bigger, to match other parts
determined controller holder placement and mounting; updated CAD for new mounting (NOTE: two holes in bottom do NOT get PEMs, like last year, see mini assembly)
change 'DIVE' to '1511' on laptop holder (just for now, incase we don't have time to work on it)
assigned part numbers for all our items and updated the names in OnShape to match
created drawings for Bottom and Power/Ethernet; create STEP of bottom
reviewed drawings

1/26 (Mon)

Attendees: Byers

Work Completed:

Assigned numbers for the Bottom and Top assemblies
created drawing for Bottom Assembly
created flat pattern files (i.e. DXF) for Bottom and Power/Ethernet
created PDF files for Bottom, Power/Ethernet, and Bottom Assembly
posted all 5 files to Teams

1/28 (Wed) V-CARVE WITH PIZZO (Lightning Bolt (Reverse) & 1511 (Reverse))

Attendees: Sami, Clara, Eric

Work Completed:

Created a 1511 stamp (0.17"H by 0.366"W)
Created a lightning bolt stamp (1.5" by 2.5")
Bottom: printed 2 copies of PDF and put in binder
Power & Ethernet: printed 2 copies of PDF and put in binder
Top: created drawing and approved, created flat pattern DXF and PDF, printed 2 copies of PDF and put in binder, posted DXF and PDF to Teams
Found a bone to put on the laptop holder.

1/29 (Thu)

Attendees: Sami, Clara, Byers

Work Completed:

Changed one '1511' to a bone in the Laptop Holder
Laptop Holder: created drawing and got approved, created a flat pattern DXF, PDF, and STEP, posted DXF, PDF, and STEP to teams, printed 2 copies of PDF and put in binder
Angle - Tiny: created drawing and got approved, created a flat pattern DXF and PDF, posted DXF and PDF to teams, printed 2 copies of PDF and put in binder
Angle - Rolling: created drawing and got approved, created a flat pattern DXF and PDF, posted DXF and PDF to teams, printed 2 copies of PDF and put in binder
Added LEDs to shopping list
Angle - LCD: created drawing and got approved, created a flat pattern DXF and PDF, posted DXF and PDF to teams, printed 2 copies of PDF and put in binder
Angle - Thunder: created drawing and got approved, created a flat pattern DXF and PDF, posted DXF and PDF to teams, printed 2 copies of PDF and put in binder
Angle - Magnets: created drawing and got approved, created a flat pattern DXF and PDF, posted DXF and PDF to teams, printed 2 copies of PDF and put in binder

1/31 (Sat)

Attendees: Sami, Eric, Byers

Work Completed:

Controller Holder: created drawing and got approved, printed 2 copies and put in binder, created STL and put in teams, updated parts and assembly log and 3D printed parts request
Controller Holder 2 : created drawing and got approved, printed 2 copies and put in binder, created STL and put in teams, updated parts and assembly log and 3D printed parts request
Added broken switches to shopping list
Found HUB, A to B USB Cable, USB for Arduino, Right Angle USB, PCB Board, Spade Connectors
Ordered power plug, Right Angle Ethernet, SD Card
Worked on Paint Scheme
Modified Broken Switches with Spade Connectors and tested
Removed Cap from 2023 PCB Board

2/1 (Sun)

Attendees: Sami, Clara, Byers

Work Completed:

Soldered LCD & Arduino headers onto PCB Board
Controls Handle: created drawing and got it approved, printed 2 copies and put in binder, created STL and put it in teams, updated parts and assembly log and 3D printed parts request
Removed back straps in the leather pouch
Cut PCB Board to length
Tested stamps
Made wire diagram

2/5 (Thu)

Attendees: Clara, Byers

Work Completed:

started controller handle 3D print
glued small piece of leather to aluminum with 5-minute epoxy as a test
cleaned up controller holders and confirmed 6-32 screw fits in the holes
changed out the VCC and GND wires on the proto board with a heavier gauge wire

2/7 (Sat)

Attendees: Sami, Clara, Byers, Eric

Work Completed:

A lot of leather working
Test fitted rivets
A lot of electrical
LCD Cage
Tested lightning bolt stamp
Made templates for leather
Stamped/Etched Leather Pieces
Finalized Paint Scheme
Picked what Brown paint we will use
submitted proto holder for 3D printing

2/8 (Sun)

Attendees: Byers

Work Completed:

tested proto board
added plastic and hit glue to proto board to protect it
fitted proto holder
started CAD for LCD Cage

2/11 (Wed)

Attendees: Sami, Clara, Eric

Work Completed:

Test fitted most items and found hardware
Countersunk three holes that needed them
Bent all rails

2/12 (Thu)

Attendees: Sami, Clara, Byers

Work Completed:

Filed sharp things
Tested magnets; 2 are enough
Tested Ethernet and power plug
Modified magnets
Confirmed LCD opening is good

2/13 (Fri)

Attendees: Byers

Work Completed:

Finished LCD Cage 3D part

2/14 (Sat)

Attendees: Sami, Clara, Byers, Eric

Work Completed:

Figured out spacing and drilled holes for leather handles
Soldered wires to LED; tested LEDs
Spray painted all parts that needed painting
Hot glued magnets into place so they are centered
LCD cage: print completed; tapped holes; mounted LCD; made USB cable hole bigger; test fitted to base
Velcroed bottom, and cut pieces to length
Found tape for LED strips

2/15 (Sun)

Attendees: Sami, Clara, Byers

Work Completed:

finalized LCD graphic layout and put on wiki
Glued leather onto top
Taped bottom of rails
Taped LEDs in
Bolted controllers in
Bolted laptop in
Snapped in power and bolted in ethernet
Velcroed power strip
Broken switches (and board) Velcroed and tested
Velcroed laptop tray
Placed the right angle ethernet in bottom (no cable management has been completed)
Velcroed controller holders
Worked on and Talked through some LCD

2/18 (Wed)

Attendees: Sami, Clara

Work Completed:

Completed Buttons (LCD Drawings)
Put tape on top of rails
Touched up top of top and resprayed bottom

2/19 (Thu)

Attendees: Sami, Clara, Byers

Work Completed:

LCD Stuff
Fixed top of Top
Got handle onto bottom

2/21 (Sat)

Attendees: Sami, Clara, Byers

Work Completed:

Cable Management
Put in and tested magnets
Changed what HUB we are using
Updated Wiki to include pictures of the physical box!
Sami used the Mill to adjust LCD box
LCD Stuff

2/22 (Sun)

Attendees: Sami, Byers, Eric

Work Completed:

Handed off controls to the software team to work with.
Put spare items in the repair kit.
Found a location for our repair kit for competition and posted it in teams

2/24 (Tue)

Attendees:

Work Completed:

2/25 (Wed)

Attendees: Eric, Sami, Byers

Work Completed:

2/26 (Thu)

Attendees:

Work Completed:

2/28 (Sat)

Attendees:

Work Completed:

3/1 (Sun)

Attendees:

Work Completed:

3/3 (Tue)

Attendees:

Work Completed:

3/4 (Wed)

Attendees:

Work Completed:

3/5 (Thu)

Attendees:

Work Completed:

3/7 (Sat)

Attendees:

Work Completed:

3/8 (Sun)

Attendees:

Work Completed:

@@ Line 1: / Line 1: @@
 == Overall Concept ==
+Physical Box:
+{| class="wikitable" style="border-collapse: collapse; width: 74.4163%;"
+|-
+| style="width: 16.4054%;" | [[image:img1771737610978.jpeg|thumb|300px]]
+| style="width: 17.3329%;" | [[image:img1771728480714.jpeg|thumb|300px]]
+| style="width: 20.7212%;" | [[image:img1771743306958.jpeg|thumb|300px]]
+| style="width: 18.027%;" | [[image:img1771735323304.jpeg|thumb|300px]]
+|-
+| style="width: 16.4054%;" | [[image:img1771812952062.jpeg|thumb|300px]]
+| style="width: 17.3329%;" | [[image:img1771815984909.jpeg|thumb|300px]]
+| style="width: 20.7212%;" | [[image:img1771793922803.jpeg|thumb|300px]]
+| style="width: 18.027%;" | [[image:img1771739951261.jpeg|thumb|300px]]
+|}
 Design Idea: Satchel
 {| style="width: 411px;"
@@ Line 42: / Line 55: @@
 * P082 Controller Holder: Black ABS
 * P083 Controller Holder 2: Black ABS
-* P111 Controls Handle: Red Filament
+* P111 Controls Handle: Red Filament, Painted Black
 Overall Dimension: 23" by 13.75" without handle
@@ Line 70: / Line 82: @@
 ** [https://www.amazon.com/ELEGOO-Compatible-Arduino-Projects-Compliant/dp/B01H4ZLZLQ/ref=sr_1_3?crid=1TV3MV1Y56EHG&dib=eyJ2IjoiMSJ9.4NfekKUziOGIHon9sPPDWjGZOsqcnTq__jEhlL8MswUrGWnpvVVjh2Jl6VBU5EHfgCOsMpqIvJ2sZvcivdpSQRvyW3pR12BicrqspIEs0igBRziJ95uy52n4nd449HW1wzsdPsQblCTJX8H7HsyUS1T7pQbVTuN-YewP9nFgNRXxuCC_1e34cjLRkZsBegkK11_7WmqGJeiq0SqHCkzoRa3xsDW0CJf2i6xCrP-tV6uZy30ZaHEMp4Sq7qOwTi46lI-MlEhM9heHE3VT2hPsIE3EmTpc6A0uN5QLQlQsJzY.ws0SxwLJDZTFXhc7khNaPC6m1KVdYHdPfuGfisIU9cg&dib_tag=se&keywords=mega2560&qid=1768785302&s=electronics&sprefix=mega2560%2Celectronics%2C93&sr=1-3&th=1 knockoff Mega 2560]
 ** [https://www.amazon.com/Arduino-ATmega2560-Compatible-Advanced-Projects/dp/B0046AMGW0/ref=sr_1_12_sspa?crid=1TV3MV1Y56EHG&dib=eyJ2IjoiMSJ9.4NfekKUziOGIHon9sPPDWjGZOsqcnTq__jEhlL8MswUrGWnpvVVjh2Jl6VBU5EHfgCOsMpqIvJ2sZvcivdpSQRvyW3pR12BicrqspIEs0igBRziJ95uy52n4nd449HW1wzsdPsQblCTJX8H7HsyUS1T7pQbVTuN-YewP9nFgNRXxuCC_1e34cjLRkZsBegkK11_7WmqGJeiq0SqHCkzoRa3xsDW0CJf2i6xCrP-tV6uZy30ZaHEMp4Sq7qOwTi46lI-MlEhM9heHE3VT2hPsIE3EmTpc6A0uN5QLQlQsJzY.ws0SxwLJDZTFXhc7khNaPC6m1KVdYHdPfuGfisIU9cg&dib_tag=se&keywords=mega2560&qid=1768785302&s=electronics&sprefix=mega2560%2Celectronics%2C93&sr=1-12-spons&sp_csd=d2lkZ2V0TmFtZT1zcF9tdGY&psc=1 Arduino Mega 2560]
-** [https://www.amazon.com/Hosyond-320x480-Capacitive-Display-Mega2560/dp/B0CRGQN58D/ref=sims_dp_d_dex_ai_rank_model_1_d_v1_d_sccl_1_1/143-6422821-6096108?pd_rd_w=HqGLj&content-id=amzn1.sym.bb4a0aac-c2b4-4b4b-a0c8-9aa89b28dce3&pf_rd_p=bb4a0aac-c2b4-4b4b-a0c8-9aa89b28dce3&pf_rd_r=M1VE2EHVAHS72M4C8QE3&pd_rd_wg=nAjhU&pd_rd_r=d58fdfa8-7597-4912-9b5f-d91c4c8c1f91&pd_rd_i=B0CRGQN58D&th=1 Capacitive Touch] <- using this one for 2026, with a Arduino Nano Every
+** [https://www.amazon.com/Hosyond-320x480-Capacitive-Display-Mega2560/dp/B0CRGQN58D/ref=sims_dp_d_dex_ai_rank_model_1_d_v1_d_sccl_1_1/143-6422821-6096108?pd_rd_w=HqGLj&content-id=amzn1.sym.bb4a0aac-c2b4-4b4b-a0c8-9aa89b28dce3&pf_rd_p=bb4a0aac-c2b4-4b4b-a0c8-9aa89b28dce3&pf_rd_r=M1VE2EHVAHS72M4C8QE3&pd_rd_wg=nAjhU&pd_rd_r=d58fdfa8-7597-4912-9b5f-d91c4c8c1f91&pd_rd_i=B0CRGQN58D&th=1 Capacitive Touch] &lt;- using this one for 2026, with a Arduino Nano Every
 *** [https://www.lcdwiki.com/4.0inch_Capacitive_SPI_Module_ST7796 specs for above LCD]
 *Thingaverse Bones:
@@ Line 87: / Line 99: @@
 {|
 | [[image:img1768484453940.jpeg|thumb|alt=LOGO Customized Leather Stamp Handle ...|300px]]
+|}
+=== LCD Layout ===
+{|
+| [[File:Layout.jpg|300px|thumb]]
 |}
 == To - Do ==
 Sami:
-Tool Test (100%) & Game Test (100%)
+* Tool Test (100%) & Game Test (100%)
+* Used the Mill for the FIRST TIME 2/21/2026
 Clara:
-Tool Test (&nbsp; &nbsp;%) & Game Test (&nbsp; &nbsp;%)
+* Tool Test (100%) & Game Test (&gt;80%/passed)
+* Artist (R - T - EAST)
 == Not Started ==
-<p>'''Design'''</p>
+* Label Broken Switches<br>
-<p>'''CAD'''</p>
+* Final mounting of the LCD.
-'''CAD Assembly'''
-<p>'''Test Fitting'''</p>
-<p>'''Final Assembly'''</p>
-<p>'''Wiring'''</p>
 == In Progress ==
+* LCD Stuff
-<p>'''Design'''</p>
-<p>'''CAD'''</p>
-* LCD Cage
-<p>'''CAD Assembly'''</p>
-<p>'''Shop Drawings'''</p>
-<p>'''Test Fitting'''</p>
-<p>'''Final Assembly'''</p>
-<p>'''Wiring'''</p>
 == Completed ==
@@ Line 158: / Line 165: @@
 * Controller Holder 2 : created drawing and got approved, printed 2 copies and put in binder, created STL and put in teams, updated parts and assembly log and 3D printed parts request
 * Control Handle: created drawing and got approved, printed 2 copies and put in the binder, created STL and put it in teams, updated parts and assembly log and 3D printed parts request
+*LCD Cage: created drawing and got approved, created STL and put in teams, updated parts and assembly log and 3D printed parts request
 '''CAD Assembly'''
 * Constrained magnets in assembly and notched end angle support
@@ Line 171: / Line 179: @@
 * Stamped/Etched Leather Pieces
 * Finalized Paint Scheme
+* Handle
+* Cable Management
+* Put in and tested magnets
 '''Wiring'''
 * Modified Broken Switches with Spade Connectors and tested
@@ Line 368: / Line 379: @@
 * Countersunk three holes that needed them
 * Bent all rails
 '''2/12 (Thu)'''
@@ Line 379: / Line 389: @@
 * Modified magnets
 * Confirmed LCD opening is good
 '''2/13 (Fri)'''
@@ Line 386: / Line 395: @@
 Work Completed:
 * Finished LCD Cage 3D part
 '''2/14 (Sat)'''
-Attendees:
+Attendees: Sami, Clara, Byers, Eric
 Work Completed:
+*Figured out spacing and drilled holes for leather handles
+*Soldered wires to LED; tested LEDs
+*Spray painted all parts that needed painting
+*Hot glued magnets into place so they are centered
+*LCD cage: print completed; tapped holes; mounted LCD; made USB cable hole bigger; test fitted to base
+*Velcroed bottom, and cut pieces to length
+*Found tape for LED strips
 '''2/15 (Sun)'''
-Attendees:
+Attendees: Sami, Clara, Byers
-Work Completed:
-'''2/17 (Tue)'''
-Attendees:
 Work Completed:
+* finalized LCD graphic layout and put on wiki
+* Glued leather onto top
+* Taped bottom of rails
+* Taped LEDs in
+* Bolted controllers in
+* Bolted laptop in
+* Snapped in power and bolted in ethernet
+* Velcroed power strip
+* Broken switches (and board) Velcroed and tested
+* Velcroed laptop tray
+* Placed the right angle ethernet in bottom (no cable management has been completed)
+* Velcroed controller holders
+* Worked on and Talked through some LCD
 '''2/18 (Wed)'''
-Attendees:
+Attendees: Sami, Clara
 Work Completed:
+* Completed Buttons (LCD Drawings)
+* Put tape on top of rails
+* Touched up top of top and resprayed bottom
 '''2/19 (Thu)'''
-Attendees:
+Attendees: Sami, Clara, Byers
 Work Completed:
+* LCD Stuff
+* Fixed top of Top
+* Got handle onto bottom
 '''2/21 (Sat)'''
-Attendees:
+Attendees: Sami, Clara, Byers
 Work Completed:
+* Cable Management
+* Put in and tested magnets
+* Changed what HUB we are using
+* Updated Wiki to include pictures of the physical box!
+* Sami used the Mill to adjust LCD box
+* LCD Stuff
 '''2/22 (Sun)'''
-Attendees:
+Attendees: Sami, Byers, Eric
 Work Completed:
+* Handed off controls to the software team to work with.
+* Put spare items in the repair kit.
+* Found a location for our repair kit for competition and posted it in teams
 '''2/24 (Tue)'''
@@ Line 444: / Line 469: @@
 '''2/25 (Wed)'''
-Attendees:
+Attendees: Eric, Sami, Byers
 Work Completed:

2026:Controls: Difference between revisions

Latest revision as of 15:23, 25 February 2026

Contents

Overall Concept

Design Info

LCD Layout

To - Do

Not Started

In Progress

Completed

Meeting Minutes

2026 Controller Map

Archives

Navigation menu

Page actions

Page actions

Personal tools

Navigation

Search

Build Season Pages

Subteam Portals

Tools