2024:Electrical Main: Difference between revisions
Line 160: | Line 160: | ||
*Investigated Solenoid/Spike Relay module, cleaned up solenoid-side terminations | *Investigated Solenoid/Spike Relay module, cleaned up solenoid-side terminations | ||
*Started initial layout of major control system components (\\penmediafs01\robotics$\2024\02 Build Season\01 Final Robot Assembly\A002 Drive Base Assembly Electrical.iam) | *Started initial layout of major control system components (\\penmediafs01\robotics$\2024\02 Build Season\01 Final Robot Assembly\A002 Drive Base Assembly Electrical.iam) | ||
*[[File:BellyPanLayout Screenshot 20242701.png|300px|thumb|Initial Electrical Layout]] | |||
= Archives = | = Archives = |
Revision as of 17:17, 27 January 2024
Known Devices
List of devices that have been established by the various mechanism groups
Sensors
Device |
Mechanism |
Detail |
Wiring notes |
Diffuse retro-reflective sensor |
Gamepiece - Intake |
Senses gamepiece |
Wire for Dark operating 12V powered Voltage divider added to cable pigtail See circuit diagram below |
Rev through-bore encoder |
Gamepiece - arm |
Used in absolute position mode to indicate arm pivot angle. |
5V powered |
Leaf lever limit switch |
Hang - brake |
Triggers when pawl on brake is fully lifted and clear of ratchet wheel |
roborio DIO |
4x CANcoder
|
Drivebase
|
One per swerve module. Indicates pivot pointing of wheel
|
|
|
|
|
|
Motors and Actuators
Device |
Mechanism |
Detail |
Wiring notes |
8 x NEOs |
Drive |
Swerve modules, one each corner of robot, each using 1 NEO for pivot and 1 NEO for propulsion |
|
NEO 550 |
Gamepiece - intake |
Runs intake to pull in or eject a game piece |
|
2 x NEOs |
Gamepiece - shooter |
Runs shooter wheels.
One NEO for top set of wheels
One NEO for bottom set of wheels |
|
NEO
|
Gamepiece - arm
|
Pivots arm
|
|
NEO 550
|
Gamepiece - arm
|
Actuates bicycle brake for arm pivot
|
|
2 x NEO |
Hang |
One NEO per hanging arm (one left, one right) Causes hang hook to go up or down |
|
2 x electric solenoid |
Hang |
Actuates braking pawl against ratchet wheel. One solenoid per arm brake (one left, one right) Energizing lifts the pawl off the ratchet wheel. Integrated spring pushes pawl into ratchet wheel |
Both solenoids controlled via one SPIKE relay (one on M+ and one on M- with common ground) |
Circuit diagrams
Allen Bradley Diffuse Circuit
Allen Bradley 42EF-D2MPAK-F4
Daily Status
' 1/20/2024
- Disassembled old batteries
- Assembled our 13 new batteries (yay!)
- Wired the prototype Game Piece mechanism for testing
- Wired the temporary test board for the new drive base for Programming to create/test swerve drive code
1/21/2024
- Spike Relay Vex wired for solenoids on hang
1/27/2024
- Updated IO Map per the Known Devices section - we should really update the PDH connections to be logical per the physical layout (see below)
- Terminated 2x solenoids for hang ratchet/pawl mechanism
- Investigated Solenoid/Spike Relay module, cleaned up solenoid-side terminations
- Started initial layout of major control system components (\\penmediafs01\robotics$\2024\02 Build Season\01 Final Robot Assembly\A002 Drive Base Assembly Electrical.iam)