2018:Robot IO Map

Robot I/O

CAN ID Assignments

ID	Subsystem	Component Type	Model #	Description (brief)	Operation	Notes (8) max. 40A         PDB #
0	Electrical	PD Module		Power Distribution Module feedback	monitor PD	must be CAN 0
1	RESERVED	n/a		Factory-default allows for adding new device quickly and re-assign its ID		don't use
2	cube intake	RS 775	Talon SRX	left	Intake cube to hand (+) eject cube (-)	30 A	6
3	cube intake	RS 775	Talon SRX	right	Intake cube to hand (+) eject cube (-)	30 A	7
4	arm	RS 775	Talon SRX	moves arm	moves from arm front (+) to back (-)	30 A	5
5	hand	RS 775	Talon SRX	hold and eject the cube	rollers intake (+) eject the cube (-)	30 A	4
6	Left Ramp, Near Jack	RS 775	Talon SRX	Raise/Lower jack	Raise jack (+)	30 A	8
7	Left Ramp, Far Jack	RS 775	Talon SRX	Raise/Lower jack	Raise jack (+) Vex encoder feeds direct to talon	30 A	10
8	Left Ramp, Far Jack	RS 775	Talon SRX	Raise/Lower jack	Raise jack (+) Vex encoder feeds direct to talon	40 A	12
9	Right Ramp, Near Jack	RS 775	Talon SRX	Raise/Lower jack	Raise jack (+) Vex encoder feeds direct to talon	40 A	3
10	Right Ramp, Far Jack	RS 775	Talon SRX	Raise/Lower jack	Raise jack (+) Vex encoder feeds direct to talon	30 A	11
11
12
13
14
15

 

PWM Outputs

ID	Subsystem	Component Type	Model #	Description (brief)	Operation	Notes (8) max. 40A              PDB #
0	DriveBase	CIM		SPARK	Left Motor 1;  +Voltage = Forwards	40A	0
0	DriveBase	CIM		SPARK	Left Motor 2; +Voltage = Forwards	40A	1
0	DriveBase	CIM		SPARK	Left Motor 3; +Voltage = Forwards	40A	2
1	DriveBase	CIM		SPARK	Right Motor 1; +Voltage = Forwards	40A	15
1	DriveBase	CIM		SPARK	Right Motor 2; +Voltage = Forwards	40A	14
1	DriveBase	CIM		SPARK	Right Motor 3; +Voltage = Forwards	40A	13
2
3
4
5
6
7
8
9

Relay Outputs

ID	Subsystem	Component Type	Model #	Description (brief)	Operation	Notes
0
1
2
3

Analog IO

RoboRIO Analog Inputs

ID	Subsystem	Component Type	Model #	Description (brief)	Operation	Voltage Range	Notes
0
1	Drive	gyro	TBD	gyro	telling angle and rate in auto
2	Arm	pot	3852A-282-103AL-ND	arm position	arm forward (+) arm back (-)	0-4 v ?
3

Rev Robotics More Board Analog IO

ID	Subsystem	Component Type	Model #	Description (brief)	Operation	Voltage Range	Notes
AIN0
AIN1
AIN2
AIN3
AOUT0
AOUT1

 

 

Digital IO (GPIO)

RoboRio IO

ID	Direction (IN/OUT)	Subsystem	Component Type	Model #	Description (brief)	Operation	Notes
0	IN	Drive	encoder	63r256	left encoder phase A	measures distance traveled	256 counts per rev
1	IN	Arm	???	???	Limit at end of travel for front of robot	Limit "switch" - digital low at limit
2	IN	Drive	encoder	63r256	right encoder phase A	measures distance traveled	256 counts per rev
3	IN	Arm	???	???	Limit at end of travel for back of robot	Limit "switch" - digital low at limit
4	IN	Intake	magnetic reed switch		Intake is all the way out	when it is all the way out it is digital low
5	IN	Arm	encoder	srx magnetic encoder	arm encoder phase A		1024 counts per rev
6	IN	Arm	encoder	srx magnetic encoder	arm encoder phase B		1024 counts per rev
7	IN
8	IN
9	IN	Hand	banner diffuse sensor	sm312fvqd	cube present	when cube is present digital low	needs 10+ volt via PD board #3

 

Rev Robotics More Board IO

ID	Direction (IN/OUT)	Subsystem	Component Type	Model #	Description (brief)	Operation	Notes
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15

I2C Registers

Address (e.g. 0100111X)	Pin (e.g. GP0)	Subsystem	Component Type	Model #	Description (brief)	Operation	Notes
0
1
2
3
4
5
6

SPI Devices

#	Subsystem	Component Type	Model #	Description (brief)	Operation	Notes

USB Host Ports

Address	Subsystem	Component Type	Model #	Description (brief)	Operation	Notes
0
1

Pneumatics Control Module

#	Subsystem	Solenoid is Double or Single?	Solenoid Model #	Description (brief)	Operation	Circuit Pressure	Notes
0	Intake	Double	SY3240-6	Raise intake	Extends cylinder to raise intake	60 PSI
1	Intake	Double	SY3240-6	Lower intake	Retracts cylinder to lower intake	60 PSI
2	Arm	Double	SY3240-6	Disengage brake on arm pivot. Does not actually pass air (block output)	Extends cylinder to disengage brake	60 PSI
3	Arm	Double	SY3240-6	Engage brake on arm pivot	Retracts cylinder to engage brake	60 PSI
4	Arm	Double	SY3240-6	Release hand's grip on cube Does not actually pass air (block output)	Removes air pressure from cylinder to "relax" grip on cube	?? PSI
5	Arm	Double	SY3240-6	Tighten hand grip on cube	Retracts cylinder to "close" hand	?? PSI
6	Ramp	Double	SY3240-6	Holds ramps in stored position	Extends cylinder to hold ramps in up position	60 PSI
7	Ramp	Double	SY3240-6	Allows ramps to deploy to ground	Retracts cylinder to release ramps to ground	60 PSI

Operator Controls

Controller 1 - Primary Driver

Button #	Action/Button	Description	Details
	Left Joystick Y
	Left Joystick X
	Right Joystick Y
	Right Joystick X
5	Left Bumper
6	Right Bumper
7	Left Trigger
8	Right Trigger
4	Y button
1	A button

Controller 2 - Aux Driver

Button #	Action/Button	Description	Details
5	Left Bumper
6	Right Bumper
8	Right Trigger
7	Left Trigger
0	Dpad Up
4	Y button
1	A button
3	X button

Broken Switches

Switch	Description	Details
Broken Switch1
Broken Switch2
Broken Switch3
Broken Switch4
Broken Switch5
Broken Switch6
Broken Switch7

IO Maps for Old Robots

• 2017 IO Map
• 2016 IO Map
• 2015 IO Map
• 2014 IO Map
• 2013 IO Map
• 2012 IO Map
• 2011 Thunderous Prime IO Map
• 2010 Thunderfoot IO Map
• 2009 Thunderplucker
• IO Pin Maps for Pre-2009 Robots