2019:Robot Design Details: Difference between revisions
From 1511Wookiee
Jump to navigationJump to search
No edit summary |
No edit summary |
||
| Line 300: | Line 300: | ||
</div> | </div> | ||
= Sensor Chart | <div class="mw-parser-output"> | ||
= Sensor Chart = | |||
{| border="1" cellpadding="10" cellspacing="1" style="width: 1236px;" | {| border="1" cellpadding="10" cellspacing="1" style="width: 1236px;" | ||
| Line 311: | Line 312: | ||
|- | |- | ||
| Intake | | Intake | ||
| | | | ||
| Senses when cylinder has completed up and down motion | | Senses when cylinder has completed up and down motion | ||
| style="width: 286px;" | On cylinder | | style="width: 286px;" | On cylinder | ||
| Line 317: | Line 318: | ||
|- | |- | ||
| Arm | | Arm | ||
| | | | ||
| Absolute rotation position of arm. | | Absolute rotation position of arm. | ||
| style="width: 286px;" | On actual pivot/shaft. | | style="width: 286px;" | On actual pivot/shaft. | ||
| Line 323: | Line 324: | ||
|- | |- | ||
| Arm | | Arm | ||
| | | | ||
| Tripped at end of travel/at hard stop on '''front '''of robot | | Tripped at end of travel/at hard stop on '''front '''of robot | ||
| style="width: 286px;" | Left side A-frame top front | | style="width: 286px;" | Left side A-frame top front | ||
| Line 329: | Line 330: | ||
|- | |- | ||
| Arm | | Arm | ||
| | | | ||
| Tripped at end of travel/at hard stop on '''back''' of robot | | Tripped at end of travel/at hard stop on '''back''' of robot | ||
| style="width: 286px;" | Left side A-frame top back | | style="width: 286px;" | Left side A-frame top back | ||
| Line 335: | Line 336: | ||
|- | |- | ||
| Hand on Arm | | Hand on Arm | ||
| | | | ||
| Sense cube '''all the way into''' hand | | Sense cube '''all the way into''' hand | ||
| style="width: 286px;" | Mounting is important! Must look "sideways" at the cube where it hits the backstop. | | style="width: 286px;" | Mounting is important! Must look "sideways" at the cube where it hits the backstop. | ||
| Line 341: | Line 342: | ||
|- | |- | ||
| Ramp | | Ramp | ||
| | | | ||
| Sense travel and speed of lead screw on lift jacks<br/> One phase | | Sense travel and speed of lead screw on lift jacks<br/> One phase | ||
| style="width: 286px;" | 4 total, 1 on each jack - Sensor should be at output stage of each gearbox | | style="width: 286px;" | 4 total, 1 on each jack - Sensor should be at output stage of each gearbox | ||
| Line 347: | Line 348: | ||
|- | |- | ||
| Ramp | | Ramp | ||
| | | | ||
| Sense when ramp jacks are fully reset (not used during match) | | Sense when ramp jacks are fully reset (not used during match) | ||
| style="width: 286px;" | 4 total, 1 on each jack - ADD MOUNTING DETAILS ONCE SENSOR IS KNOWN | | style="width: 286px;" | 4 total, 1 on each jack - ADD MOUNTING DETAILS ONCE SENSOR IS KNOWN | ||
| Line 353: | Line 354: | ||
|- | |- | ||
| Drive | | Drive | ||
| | | | ||
| Travel of robot drive base. '''One phase''' | | Travel of robot drive base. '''One phase''' | ||
| style="width: 286px;" | On center (traction) wheel shaft. | | style="width: 286px;" | On center (traction) wheel shaft. | ||
| Line 374: | Line 375: | ||
| style="width: 147px;" | | | style="width: 147px;" | | ||
|} | |} | ||
</div> | |||
= Archive = | = Archive = | ||
Revision as of 10:33, 12 January 2019
Overall design decisions, notes, specifications, and integration items here! Integration Task List (NEEDS LINK HERE)
Overall Robot Dimensional Restraints
Last updated: 1/9/2019
| Length | Width | Perimeter | |
|---|---|---|---|
| Robot Boundary | 34" | 24" | 116" |
Drive Base Materials
| Function | Material |
|---|---|
| Perimeter Rail (Long Side) | 1"x3"x1/8" 6061 Aluminum Angle Stock |
| Inner Rail (Long Side) | 1"x3"x1/8" 6061 Aluminum Channel Stock |
| Perimeter Rail (Short Side) | TBD |
Actuators
THE FOLLOWING TABLES ARE COPIES OF 2018's TABLES AND HAVE BEEN LEFT FOR ILLUSTRATION ONLY - DO NOT USE FOR 2019! Please delete the above note and replace content of the tables below with 2019-relevant information once available.
Motors
| Mechanism | Action | Minimum Breaker Size | Motor Model # | Quantity | Notes |
| Hatch | picks up and deploys the hatch | n/a | see pneumatic actuators | ||
| Cargo | picks up and deploys the cargo | ? tbd | non CIM | 1-2 | need to determine side to side or vertical wheels |
| Elevator | moves the cube and hatch mechanisms up and down | ? tbd | non CIM | 2 |
gear ratio tbd |
| Elevator | rotates the elevator in and out of frame perimeter | n/a | planned to be a piston | ||
| Habitat |
Lifts the robot onto level 2 or 3 |
n/a |
see pneumatic actuators | ||
| Habitat | rotates wheels/skids in front of bumpers | tbd | could be piston | ||
| Drive Base | Moves the robot | 40A | CIM | 4 |
Gear ratio 14:68 option to add two additional motors option to swap out CIMs to Neos |
Pneumatics
| Mechanism | Action - Say what extend and retract do! | Number of Cylinders | Cylinder | Extend Powered? | Extend Exhaust to Atmosphere? | Retract Powered? | Retract Exhaust to Atmosphere? | Working Pressure | Estimated Firings per Match (Sum of all powered directions!) |
Notes |
| Hatch | Extend = raises the hook Retract = lowers the hook |
1 |
Bimba tbd estimated 3/4" bore 1" stroke |
Yes | no | no ?possibly spring loaded | Yes | 40 PSI | 12 (24 if not spring loaded) |
|
| Hatch |
Extend = brings it out past the cargo Retract= brings it back in |
1 |
Bimba tbd estimated 3/4" bore 2-4" stroke |
yes | no | yes | no | 40 psi | 24 | |
| Cargo (side wheels) |
Extend=brings the wheels into the cargo Retract= opens the wheels |
2 |
Bimba tbd estimated 3/4" bore 3" stroke |
yes | yes | yes | yes | 40 psi | 24 * | * total cycles of cargo and hatch combined will not exceed 12 (24 if dual action) |
| Elevator |
extend= places elevator in match position retract= places elevator in starting config. |
1 |
Bimba tbd estimated 1.5" bore 18" stroke |
yes | yes | yes | yes | 60 psi | 2 (depending on if we do defense) | |
| Elevator Brake |
Extend (spring loaded extension) = disengage brake Retract = Engage brake |
1 | Bimba 041-D. 3/4" bore 1" stroke | No | Yes | Yes | Yes | 60 PSI |
18 |
12 cycles plus adjustment factor |
| Habitat skids |
Extend = deploys the skids Retract = brings the skids back in |
2 |
Bimba tbd 3/4" bore 2" stroke |
yes | Yes | no | no | 60 psi |
1 |
|
|
Habitat Lift
|
Extend = lifts the robot Retract = keeps us from being technically supported by level one |
2 |
Bimba tbd 2" bore, 22" stroke |
Yes | Yes | Yes | Yes | 60 PSI |
2 |
|
Sensor Chart
| Mechanism | Sensor Type | Function | Attachment Point | Notes |
| Intake | Senses when cylinder has completed up and down motion | On cylinder | ||
| Arm | Absolute rotation position of arm. | On actual pivot/shaft. | ||
| Arm | Tripped at end of travel/at hard stop on front of robot | Left side A-frame top front | ||
| Arm | Tripped at end of travel/at hard stop on back of robot | Left side A-frame top back | ||
| Hand on Arm | Sense cube all the way into hand | Mounting is important! Must look "sideways" at the cube where it hits the backstop. | ||
| Ramp | Sense travel and speed of lead screw on lift jacks One phase |
4 total, 1 on each jack - Sensor should be at output stage of each gearbox | ||
| Ramp | Sense when ramp jacks are fully reset (not used during match) | 4 total, 1 on each jack - ADD MOUNTING DETAILS ONCE SENSOR IS KNOWN | ||
| Drive | Travel of robot drive base. One phase | On center (traction) wheel shaft. | ||
| Whole robot | Gyro | Sense rotation | Must be center of rotation of robot away from excessive vibration sources | |
| Whole robot | Camera |
Visual feedback for lining up with exchange? MS LifeCam HD USB camera |
On the back left corner of the robot in the area set aside in cad |
